Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
  • Manage your Dell EMC sites, products, and product-level contacts using Company Administration.
Sign In Create an Account Dell Financial Services Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell VxRail VD-4510c Hardware Requirements and Specifications

PDF

Configurations and features

The VxRail VD-4510c is a 1U half-width, 1-processor server sled that supports:
  • A Third-Generation Intel Xeon D Scalable processor with up to 16 cores
  • Four DDR4 DIMM slots
  • Up to 4 x M.2 NVMe SSDs

The following figure and table describes the components on the front view of the sled:

Front view of the sled
Item Component
1 Network I/O ports for network connectivity. Ports shared with iDRAC when iDRAC network settings are set to shared mode.
2 Serial port
3 USB 9 pin and 3.0 compliant port
4 iDRAC9 RJ45 dedicated port for remote access to iDRAC. See the Integrated Dell Remote Access Controller User's Guide.
5 Mini-Display Port
6 Sled handle
7 System ID button is available on the front and back. Press System ID to identify a system in the rack, reset iDRAC, and access BIOS using the step-through mode. When pressed, the System ID LED in the back panel blinks until the front or rear button is pressed again. Press the System ID to switch between on and off.

If the server stops responding during POST, press and hold the System ID button for more than five seconds to enter the BIOS progress mode.

To reset the iDRAC (if not disabled on the iDRAC setup page by pressing F2 during system boot), press and hold the System ID button for more than 15 seconds.

8 Sled Power button

When VxRail VD-4510c is installed in the VxRail VD-4000r or VxRail VD-4000z chassis, the power button LED indicator status may be delayed for up to two minutes while the sled is initializing. The power button LED will start slowly blinking to indicate the system is performing the power on sequence after this time period

9 iDRAC Direct port (Micro-AB USB) allows access to the iDRAC direct Micro-AB USB features.
10 Information tag is a slide-out label panel that contains one MAC address
11 Bezel pogo pin connector is a spring-loaded, pressure sensitive sensor that indicates when replacement is needed.

The following figure and table describes the components on the rear view of the sled:

Rear view of the sled
Item Component
1 Connector cover
2 Cooling fans
3 Power Interposer Board (PIB) connection switch

The following figure shows the components inside the VxRail VD-4510c sled:

Inside view of the PowerEdge XR4510c sled
Item Component
1 Processor and heat sink
2 M.2 SSD module
3 System board
4 Processor
5 Network I/O ports
6 Sled handle
7 Information tag
8 M.2 Riser module
9 M.2 BOSS N1 card
10 Fan guard
11 Fan
The following figure and table describes the components in the rear view of the sled:
This image shows the rear view of the sled.
The following table describes rear view components:
Item Description
1 Upper layer connector cover
2 Upper layer power interposer board (PIB) connector switch
3 Upper layer fans rear view
4 Bottom layer fans rear view
5 Bottom layer power interposer board (PIB) connector switch
6 Bottom layer connector cover
The following figure shows the inside view:
Inside view of the PowerEdge XR4520c sled.
This table describes the components inside the sled:
Item Component
1 Connector cover
2 Fan handle
3 Power Interposer board (PIB)
4 Riser R1C card
5 2U sled side cover
6 2U sled cooling fan

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\