Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

portmode hybrid

To accept both tagged and untagged frames, set a physical port or port-channel. A port configured this way is identified as a hybrid port in report displays.

Syntax

portmode hybrid

To return a port to accept either tagged or untagged frames (non-hybrid), use the no portmode hybrid command.

Defaults

non-hybrid

Command Modes

INTERFACE (conf-if- interface-slot/port)

Supported Modes

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.2(0.0)	Introduced on the M I/O Aggregator.
8.3.16.1	Introduced on the MXL 10/40GbE Switch IO Module.

Usage Information

The following describes the interface command shown in the following example. This example sets a port as hybrid, makes the port a tagged member of VLAN 20, and an untagged member of VLAN 10, which becomes the native VLAN of the port. The port now accepts:

untagged frames and classify them as VLAN 10 frames
VLAN 20 tagged frames

The following describes the do show interfaces command shown in the following example. This example shows output with “Hybrid” as the newly added value for 802.1QTagged. The options for this field are:

True — port is tagged
False — port is untagged
Hybrid — port accepts both tagged and untagged frames

The following describes the interface vlan command shown in the following example. This example shows unconfiguration of the hybrid port using the no portmode hybrid command.

NOTE: Remove all other configurations on the port before you can remove the hybrid configuration from the port.

Example

Dell(conf)#interface tengig 0/2
                                             Dell(conf-if-te-0/2)#no shut
                                             Dell(conf-if-te-0/2)#portmode hybrid
                                             Dell(conf-if-te-0/2)#sw
                                             Dell(conf-if-te-0/2)#int vlan 10
                                             Dell(conf-if-vl-10)#tag tengig 0/2
                                             Dell(conf-if-vl-10)#int vlan 20
                                             Dell(conf-if-vl-20)#untag tengig 0/2
                                             Dell(conf-if-vl-20)#

Example (tagged hybrid)

Dell(conf)#interface tengig 0/2
                                             Dell(conf-if-te-0/2)#no shut
                                             Dell(conf-if-te-0/2)#portmode hybrid
                                             Dell(conf-if-te-0/2#sw
                                             Dell(conf-if-te-0/2)#int vlan 10
                                             Dell(conf-if-vl-10)#int tengig 0/2
                                             Dell(conf-if-vl-20)# untag tengig 0/2
                                             
                                             Dell (conf-if-vl-20)#
                                             
                                             Dell(conf)#do show interfaces switchport tengigabitethernet 3/2
                                             
                                             Codes: U - Untagged, T - Tagged
                                             x - Dot1x untagged, X - Dot1x tagged
                                             G - GVRP tagged, M - Trunk, H - VSN tagged
                                             i - Internal untagged, I - Internal tagged, v - VLT untagged,
                                             V - VLT tagged
                                             
                                             Name: TenGigabitEthernet 3/2
                                             
                                             802.1QTagged: Hybrid
                                             Vlan membership:
                                             Q   Vlans
                                             U   20
                                             T   10
                                             
                                             Native VlanId: 20.
                                             
                                             Dell(conf)#

Example (unconfigure the hybrid port)

Dell(conf-if-vl-20)#interface vlan 10
                                             Dell(conf-if-vl-10)#no untagged tengig 0/2
                                             Dell(conf-if-vl-10)#interface vlan 20
                                             Dell(conf-if-vl-20)#no tagged tengig 0/2
                                             Dell(conf-if-vl-20)#interface tengig 0/2
                                             Dell(conf-if-te-0/2)#no portmode hybrid
                                             Dell(conf-if-vl-20)#

Related Commands

show interfaces switchport — displays the configuration of switchport (Layer 2) interfaces on the switch.

vlan-stack trunk— specifies an interface as a trunk port to the Stackable VLAN network.