Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

seq

Configure a filter with an assigned sequence number for the redirect list.

Syntax seq sequence-number {permit | redirect { ip-address | tunnel tunnel-id}[track <obj-id>] }}{ ip-protocol-number | protocol-type} { source mask | any | host ip-address} { destination mask | any | host ip-address} [bit] [ operator]{source-port source-port| source-port-range start-port - end-port} {destination-port destination-port| destination-port-range start-port - end-port}

To delete a filter, use the no seq sequence-number command.

Parameters
sequence-number Enter a number from 1 to 65535.
permit Enter the keyword permit assign the sequence to the permit list.
redirect Enter the keyword redirect to assign the sequence to the redirect list.
ip-address Enter the IP address of the forwarding router.
tunnel Enter the keyword tunnel to configure the tunnel setting.
tunnel-id Enter the keyword tunnel-id to redirect the traffic.
track Enter the keyword track to enable the tracking.
track <obj-id> Enter the keyword track <obj-id> to track object-id.
ip-protocol-number Enter the keyword ip-protocol-number then the number from 0 to 255 for the protocol identified in the IP protocol header.
protocol-type Enter one of the following keywords as the protocol type:
  • icmp for internet control message protocol
  • ip for any internet protocol
  • tcp for transmission control protocol
  • udp for user datagram protocol
source Enter the IP address of the network or host from which the packets were sent.
mask Enter a network mask in /prefix format (/x).
any Enter the keyword any to specify that all traffic is subject to the filter.
host ip-address Enter the keyword host then the IP address to specify a host IP address.
destination Enter the IP address of the network or host to which the packets are sent.
bit (OPTIONAL) For the TCP protocol type only, enter one or a combination of the following TCP flags:
  • ack = acknowledgement
  • fin = finish (no more data from the user)
  • psh = push function
  • rst = reset the connection
  • syn = synchronize sequence number
  • urg = urgent field
operator (OPTIONAL) For the TCP and UDP parameters only. Enter one of the following logical operand:
  • eq = equal to
  • neq = not equal to
  • gt = greater than
  • lt= less than
  • range = inclusive range of ports (you must specify two ports for the port command parameter.)
source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule
destination-port Enter the keywords destination-port then the port number to be matched in the ACL rule in the ICAP rule.
source-port-range Enter the keywords Source-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
destination-port-range Enter the keywords destination-port-range then the range of the start port to end port to be matched in the ACL rule in the ICAP rule.
Defaults none
Command Modes REDIRECT-LIST
Supported Modes Full—Switch
Command History
Version Description
9.9(0.0) Introduced on the FN IOM.
9.7(0.0) Added support for the track-id on the MXL.
9.4(0.0) Added support for removing the Sonet interface on the MXL 10/40GbE Switch IO Module.

Califique este contenido

Preciso
Útil
Fácil de comprender
¿Este artículo fue útil?
0/3000 characters
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Proporcione calificaciones (1 a 5 estrellas).
  Seleccione si el artículo fue útil o no.
  Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"