Create a deployment template from a reference device
Create a deployment template by capturing the configuration from a managed device.
Prerequisites
To perform any tasks on OpenManage Enterprise, you must have the necessary user privileges. See
Role and scope-based access.
Reference chassis or PowerEdge 12 and 13-generation servers should be running iDRAC firmware later than version 2.50.50.50.
With HTTPS-enabled internal shares, deployment template creation is not supported on MX7000 sleds that are discovered using the Complete Chassis Discovery (CCD).
With SMBv2-enabled CIFS share, deployment template creation is not supported on Fx2: 2.21 and, VRTX 3.21 devices.
To create a template with custom telemetry configuration, ensure that the server has a valid iDRAC DataCenter license and the iDRAC firmware is 4.40 and above.
About this task
You can create or edit a deployment template by using a reference device or by importing from an existing deployment template.
Steps
Click
Configuration > Templates > Create Template, and then select
From Reference Device.
In the
Create Template
dialog box:
In the
Template Information section, enter a name for the deployment template and a description for the template.
NOTE:The only special characters that are allowed in the
Template Name are alphanumeric, dash, underscore, and space.
Select the Deployment template type:
Clone Reference Server: Enables you to clone the configuration of an existing server.
NOTE:The
Custom Telemetry option is available only when the
Template Type is selected as
Clone Reference Server and these configurations are captured only if the target server has a valid data center license.
Clone Reference Chassis: Enables you to clone the configuration of an existing chassis.
Clone Reference IOA: Enables you to clone the configuration of an existing M I/O aggregator.
NOTE:
The attributes in the IOA template are uneditable, only the
name and
description of an IOA template can be edited.
Click
Next.
In the
Reference Device section, click
Select Device to select the device whose configuration properties are used for creating the deployment template. For more information about selecting devices, see
Selecting target devices and device groups.
You can select only one device as a reference device.
In the
Configuration Elements section, select the check boxes corresponding to the device elements that must be cloned. For creating a deployment template by using server as the device, select to clone the server properties such as iDRAC, BIOS, Lifecycle Controller, and Event Filters. By default, all elements are selected.
Optional: To enable custom telemetry configuration, under
Additional Elements, select
Custom Telemetry.
NOTE: Custom telemetry configuration is available only when the
Template Type is selected as
Clone Reference Server, and this configuration is enabled only if the target server has a valid data center license.
Click
Finish.
After successful creation, the job is displayed in the list. A deployment template creation job starts, and its status is displayed in the
STATUS column.
The job information is also displayed on the
Monitor > Jobs screen. To view additional details of the job:
Select the job.
Click
View Details in the working pane.
On the
Job Details screen, you will find the execution details of the job.
In the
Results pane, click
View Details to view detailed information of the job execution.
Results
When creating a template with a custom telemetry option selected on a server, the deployment template creation task marks the job as completed in the Job Details. However, a warning appears in the task execution details indicating:
Custom telemetry was requested but not received from the target.. The warning occurs because of the following reasons:
The server was discovered through CCD.
The server does not have a valid data center license or valid a telemetry configuration.
Next steps
Templates that are created from a reference device may contain a discovery password. When deployed on target devices, this can cause communication failure. To resolve this issue:
After deployment, rediscover the device with the new credentials.
Export the SCP reference from the iDRAC without password hash values and import it to OpenManage Enterprise. Optionally, set the password value by editing the attributes and deploying it.
Data is not available for the Topic
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\