Configure and bring up SRDF/Star
|
setup -options
buildcg (at the Target sites)
connect
protect
enable
|
Sample procedure showing the basic steps to configure and activate the SRDF/Star environment after the CG has been created.
|
W
|
Displaying the symstar configuration
symstar show command
symstar list command
|
query
show
list
|
- Displays the status of a given SRDF/Star site configuration.
- Displays the contents of the internal definition for a given SRDF/Star site configuration.
- Lists each SRDF/Star composite group configuration, including workload name, mode of operation, CG and Star states, and target names and states.
|
W/T
|
Removal of a CG from SRDF/STAR control
|
setup -remove
|
Removes the CG from Star control.
|
|
Isolate SRDF/Star sites
|
isolate
|
Isolates one target site from the SRDF/Star configuration and makes its R2 devices read/write enabled to their hosts.
|
W
|
Unprotect target sites
|
unprotect
|
Disables SRDF/Star consistency protection to the specified target site.
|
W
|
Halt target sites
|
halt
|
Used to prepare SRDF/Star for a planned switch of the workload to a target site. This action write-disables the R1 devices, drains all invalid tracks and MSC cycles so that NewYork=NewJersey=London, suspends SRDF links, disables all consistency protection, and sets adaptive copy disk mode.
|
W/T
|
Clean up metadata
|
cleanup
|
Cleans up internal meta information and cache at the remote site after a failure at the workload site.
|
T
|
SRDF/Star consistency group operations
|
modifycg
|
Maintains consistency protection when adding or removing device pairs from an SRDF/Star consistency group.
|
W
|
Upgrade an existing SRDF/Star environment
Transition SRDF/Star to use R22 devices
|
configure
|
Upgrades or transitions an existing SRDF/Star environment to employ R22 devices, provided the current SRDF/Star environment is operating in normal condition.
|
W
|
Begin SRDF synchronization
|
connect
|
Starts the SRDF data flow in adaptive copy disk mode.
|
W
|
Enable full SRDF/Star protection
|
enable
|
Enables complete SRDF/Star consistency protection across the three sites.
|
W
|
SRDF/Star consistency group operations
|
protect
|
Synchronizes devices between the workload and target sites and enables SRDF/Star consistency protection to the specified target site.
|
W
|
Change the SRDF/Star replication path
Reconfiguring mode: cascaded to concurrent,Reconfiguring cascaded paths,Reconfiguring mode: concurrent to cascaded,Reconfigure mode without halting the workload site
|
reconfigure
|
Transitions the SRDF/Star setup from concurrent SRDF to cascaded SRDF or vice versa after a site or link failure, or as part of a planned event.
|
W
|
Reset after a transient failure
Recovery operations: Concurrent SRDF/Star,
Recovery operations: Cascaded SRDF/Star
|
reset
|
Cleans up internal meta information and cache at the remote site after transient fault (such as a loss of connectivity to the synchronous or asynchronous target site).
|
W
|
Switch workload operations to a target site
Workload switching: Concurrent SRDF/Star,
Unplanned workload switching: cascaded SRDF/StarUnplanned workload switching to asynchronous target site: Cascaded SRDF/Star
|
switch
|
Transitions workload operations to a target site after a workload site failure or as part of a planned event.
|
T
|
Verify that the given site or SRDF/Star setup is in the desired state
Displaying the symstar configuration
|
verify
|
Returns success if the state specified by the user matches the state of the Star setup.
|
W/T
|