PowerScaleOneFS CLI Command Reference

Syntax

isi network subnets modify <id>
  [--description <string>|--clear-description]
  [--name <string>]
  [--dsr-addrs <ip_address>|--clear-dsr-addrs
  | --add-dsr-addrs <ip_address>|--remove-dsr-addrs
  <ip_address>]
  [--revert-dsr-address]
  [--gateway <ip-address>]
  [--gateway-priority <integer>]
  [--mtu <integer>]
  [--revert-mtu]
  [--prefixlen <prefixlen>]
  [--vlan-enabled <boolean>
  [--revert-vlan-enabled]  
  [--vlan-id <integer>]
  [--sc-service-addr <ip_address_range>
  | --clear-sc-service-addrs|--add-sc-service-addrs
  <ip_address_range> | --remove-sc-service-addrs <ip_address_range>]
  [--sc-service-name <domain_name>]
  [{--force | -f}]
  [{--verbose | -v}]
  

Options

<id>

Specifies the ID of the subnet that you want to modify. A subnet ID consists of a <groupnet_id>, followed by a ':', followed by a subnet name. A subnet name must be unique throughout the cluster, and can be up to 32 characters long. Supported characters are [a-zA-Z0-9-_]. The <groupnet_id> and ':' may be left off if the subnet is in the default groupnet.

A subnet in a groupnet: "example_groupnet:example_subnet"
        A subnet in the default groupnet: "example_subnet"

The groupnet name is optional if referring to the default groupnet0. Colons are also acceptable as delimiters between component names—for example, groupnet0:subnet1.

--description <string>

Specifies an optional description of the subnet. The description cannot exceed 128 bytes.

--clear-description

Clears the description of the subnet.

--dsr-addrs <ip_address>...

Specifies a list of IP addresses that use Direct Server Return (DSR). You need to specify --dsr-addrs for each additional IP address.

NOTE:This option has been deprecated.

--clear-dsr-addrs

Clears list of IP addresses that use Direct Server Return.

NOTE:This option has been deprecated.

--add-dsr-addrs <ip_address>...

Adds items to the list of IP addresses that use Direct Server Return. You need to specify--add-dsr-addrs for each additional IP address that you want to add.

NOTE:This option has been deprecated.

--remove-dsr-addrs <ip_address>...

Removes items from the list of IP addresses that use Direct Server Return. You need to specify --remove-dsr-addrs for each additional IP address that you want to remove.

NOTE:This option has been deprecated.

--revert-dsr-addrs

Sets the value of --dsr-addrs to the system default value.

NOTE:This option has been deprecated.

--gateway <ip_address>

Specifies the gateway IP address used by the subnet.

--gateway-priority <integer>

Specifies priority of the subnet gateway, where the lowest number is of the highest priority.

--mtu <integer>

Sets the size of the maximum transmission unit (MTU) of the subnet that the cluster uses in network communication.

--revert-mtu

Sets the value of --mtu to the system default value.

--prefixlen <iprefixlen>

Sets the prefix size of the subnet.

--name <string>

Specifies the name for the subnet.

--sc-service-addrs <ip_address_range>...

Specifies a range of IP addresses in the subnet which will receive incoming DNS requests. You need to specify --sc-service-addrs for each additional IP address.

--clear-sc-service-addrs

Clears the list of SmartConnect Service IP addresses.

--add-sc-service-addrs <ip_address_range>...

Adds the items to the list of SmartConnect Service IP addresses. You need to specify --add-sc-service-addrs for each additional IP address you want to add.

--remove-sc-service-addrs <ip_address_range>...

Removes the items from the list of SmartConnect Service IP addresses. You need to specify --remove-sc-service-addrs for each additional IP address you want to remove.

--sc-service-name <domain_name>

Specifies the domain name corresponding to the SmartConnect Service IP address.

This option is used in DNS Start of Authority (SOA) and Name Server (NS) records to correctly identify the SmartConnect DNS server. If this domain name does not correspond to the SmartConnect Service IP on your DNS server, it can cause unavailability of SmartConnect.

Use of this field is optional.

--vlan-enabled <boolean>

Enables VLAN tagging on the subnet.

--revert-vlan-enabled

Sets the value of --vlan-enabled to the system default value.

--vlan-id <integer>

Specifies the VLAN ID for all interfaces on this subnet.

{--force | -f }

Suppresses any prompts or warnings messages that would otherwise appear before or during the subnet modification operation.

{--verbose | -v}

Displays more detailed information.

{--help | -h}

Displays help for this command.