OptiPlex Small Form Factor 7010 Owner's Manual

PDF

System setup options

NOTE:Depending on this computer and its installed devices, the items listed in this section may or may not appear.

Table 1. System setup options—System information menu
The following table describes the System information menu options in the System setup program.
General-System Information
	System Information
	BIOS Version	Displays the BIOS version number.
	Service Tag	Displays the Service Tag of the computer.
	Asset Tag	Displays the Asset Tag of the computer.
	Ownership Tag	Displays the ownership tag of the computer.
	Manufacture Date	Displays the manufacture date of the computer.
	Ownership Date	Displays the ownership date of the computer.
	Express Service Code	Displays the express service code of the computer.
	Signed Firmware Update	Displays the signed firmware update of the computer.
	Memory Information
	Memory Installed	Displays the total computer memory installed.
	Memory Available	Displays the total computer memory available.
	Memory Speed	Displays the memory speed.
	Memory Channel Mode	Displays single or dual channel mode.
	Memory Technology	Displays the technology used for the memory.
	DIMM 1 Size	Displays the DIMM 1 memory size.
	DIMM 2 Size	Displays the DIMM 2 memory size.
	DIMM 3 Size	Displays the DIMM 3 memory size.
	DIMM 4 Size	Displays the DIMM 4 memory size.
	Processor Information
	Processor Type	Displays the processor type.
	Core Count	Displays the number of cores on the processor.
	Processor ID	Displays the processor identification code.
	Current Clock Speed	Displays the current processor clock speed.
	Minimum Clock Speed	Displays the minimum processor clock speed.
	Maximum Clock Speed	Displays the maximum processor clock speed.
	Processor L2 Cache	Displays the Processor L2 Cache size.
	Processor L3 Cache	Displays the Processor L2 Cache size.
	Microcode Version	Displays whether the microcode version.
	Intel Hyper-Threading Capable	Displays whether the computer is Intel Hyper-Threading capable.
	64-Bit Technology	Displays whether 64-bit technology is used.
	Device Information
	Slot 1	Displays the slot 1 information of the computer.
	Slot 2	Displays the slot 2 information of the computer.
	LOM MAC Address	Displays the LOM MAC address of the computer.
	Video Controller	Displays the video controller type of the computer.
	Video Memory	Displays the video memory of the computer.
	Native Resolution	Displays the native resolution of the computer.
	Video BIOS version	Displays the video BIOS version of the computer.
	Audio Controller	Displays the audio controller information of the computer.
	Wi-Fi Device	Displays the wireless device information of the computer.
	Bluetooth Device	Displays the Bluetooth device information of the computer.
	dGPU Video Controller	Displays the dGPU video controller of the computer.

Table 2. System setup options—Boot Configuration menu
The following table describes the System Configuration menu options in the System setup program.
Boot Configuration
	Boot Sequence
	Boot Sequence	Displays the boot sequence.
	Boot List Option	Displays the available boot options.
	Force PXE on Next Boot	This option is disabled by default.
	Secure Digital (SD) Card Boot	This option is disabled by default.
	Secure Boot
	Enable Secure Boot	This option is disabled by default.
	Enable Microsoft UEFI CA	This option is enabled by default.
	Secure Boot Mode	The option Deployed mode is enabled by default.
	Expert Key Management
	Enable Custom Mode	This option is disabled by default.
	Custom Mode Key Management	The option PK is enabled by default.

Table 3. System setup options—Integrated devices
The following table describes the Video menu options in the System setup program.
Integrated Devices
	Date/Time		Displays the date and time configuration of the computer.
	Memory Mapped I/O above 4 Gig		This option is enabled by default.
	Audio		The option Enable Audio is enabled by default.
	USB configuration		All options are enabled by default.
	Front USB configuration		All options are enabled by default.
	Rear USB configuration		All options are enabled by default.
	Dust Filter Maintenance		The disabled option is enabled by default.

Table 4. System setup options—Storage
The following table describes the storage menu options in the System setup program.
Storage
	SATA/NVMe Operation	The option RAID on is enabled by default.
	Storage Interface	All options are enabled by default.
	SMART Reporting	This option is disabled by default.
	Drive information	Displays drive information about this computer.
	Enable MediaCard	The option Secure Digital SD card is enabled by default.

Table 5. System setup options—Display
The following table describes the Display menu options in the System setup program.
Display
	Multi-Display	This option is enabled by default.
	Primary display	The auto option is enabled by default.
	Full screen logo	This option is disabled by default.

Table 6. System setup options—Connection
The following table describes the connection menu options in the System setup program.
Connection
	Network Controller Configuration
	Integrated NIC	The option Enabled with PXE is enabled by default.
	Wireless Device Enable	WLAN and Bluetooth options are enabled by default.
	Enable UEFI Network Stack	The option Auto Enabled is enabled by default.
	HTTP(s) Boot Feature	The option is enabled by default.
	HTTP(s) Boot Mode	The Auto Mode option is enabled by default.

Table 7. System setup options—Power
The following table describes the Power menu option in the System setup program.
Power
	USB PowerShare	This option is disabled by default.
	USB Wake Support	The option is enabled by default.
	AC Behavior	The Power Off option is enabled by default.
	Active State Power Management	The option Auto is enabled by default.
	Block Sleep	The option is disabled by default.
	Deep Sleep Control	The option Enabled in S4 and S5 is enabled by default.
	Fan Control Override	This option is disabled by default.
	Intel Speed Shift Technology	This option is enabled by default.

Table 8. System setup options—Security
The following table describes the Security options in the System setup program.
Security
	TPM 2.0 Security	The option is enabled by default.
	Attestation Enable	This option is enabled by default.
	Key Storage Enable	This option is enabled by default.
	SHA-256	This option is enabled by default.
	Clear	This option is disabled by default.
	PBI Bypass for Clear Commands	This option is disabled by default.
	Intel Total Memory Encryption	The Multi-Key Total Memory Encryption (Up to 16 keys) option is disabled by default.
	SMM Security Mitigation	This option is disabled by default.
	Absolute	This option is enabled by default.
	Chassis intrusion	This option is disabled by default.
	Block Boot Until Cleared	This option is disabled by default.
	Data Wipe on Next Boot	This option is disabled by default.
	UEFI Boot Path Security	The option Always Except Internal HDD is enabled by default.
	Authenticated BIOS interface	This option is disabled by default.
	Legacy Manageability Interface Access	This option is disabled by default.

Table 9. System setup options—Passwords menuThe following table describes the Passwords options in the System setup program.
Passwords
	Admin Password	Set, change, or delete the administrator password.
	System Password	Set, change, or delete the computer password.
	Internal HDD-0 Password	Set, change, or delete the Internal HDD-0 password.
	M.2 PCIe SSD-0	Set, change, or delete the M.2 PCIe SSD-0 password.
	Password Configuration
	Upper Case Letter	Reinforces password must have at least one upper case letter. By default, the option is disabled.
	Lower Case Letter	Reinforces password must have at least one lower case letter. By default, the option is disabled.
	Digit	Reinforces password must have at least one digit. By default, the option is disabled.
	Special Character	Reinforces password must have at least one special character. By default, the option is disabled.
	Minimum Characters	Set the minimum characters allowed for password.
	Password Bypass	When enabled, this always prompts for computer and internal hard drive passwords when powered on from the off state. By default, the Disabled option is enabled.
	Password Changes
	Enable Non-Admin Password Changes	Enable or disable to change computer and hard drive password without the need for admin password. By default, the option is enabled.
	Admin Setup Lockout
	Enable Admin Setup Lockout	Enables administrators control over how their users can or cannot access BIOS setup. By default, the option is disabled.
	Master Password Lockout
	Enable Master Password Lockout	When enabled, this will disable the master password support. By default, the option is disabled.
	Allow Non-Admin PSID Revert
	Enable Allow Non-Admin PSID Revert	Controls access to the Physical Security ID (PSID) revert of NVMe hard-drives from the Dell Security Manager prompt. By default, the option is disabled.

Table 10. System setup options—Update, Recovery menu The following table describes the Update, Recovery options in the System setup program.
Update, Recovery
	UEFI Capsule Firmware Updates	Enable or disable BIOS updates through UEFI capsule update packages. By default, the option is enabled.
	BIOS Recovery from Hard Drive	Enables the user to recover from certain corrupted BIOS conditions from a recovery file on the user primary hard drive or an external USB key. By default, the option is enabled.
	BIOS Downgrade
	Allow BIOS Downgrade	Enable or disable the flashing of the computer firmware to previous revision is blocked. By default, the option is enabled.
	SupportAssist OS Recovery	Enable or disable the boot flow for SupportAssist OS Recovery tool in the event of certain computer errors. By default, the option is enabled.
	BIOSConnect	Enable or disable cloud Service OS recovery if the main operating system fails to boot with the number of failures equal to or greater than the value specified by the Auto OS Recovery Threshold setup option and local Service OS does not boot or is not installed. By default, the option is enabled.
	Dell Auto OS Recovery Threshold	Controls the automatic boot flow for SupportAssist System Resolution Console and for Dell OS Recovery Tool. By default, the threshold value is set to 2.

Table 11. System setup options—System Management menu The following table describes the System Management menu options in the System setup program.
System Management
	Service Tag	Display the Service Tag of the computer.
	Asset Tag	Create a computer Asset Tag.
	Wake on LAN/WLAN	Enable or disable the computer to power on by special LAN signals when it receives a wakeup signal from the WLAN. By default, the Disabled option is selected.
	Auto on Time	Enable to set the computer to turn on automatically every day or on a preselected date and time. This option can be configured only if the Auto On Time is set to Everyday, Weekdays, or Selected Days. By default, the option is disabled.
	SERR Messages	Enable or disable SERR messages. By default, the option is enabled.
	First Power On Date	The Set Ownership Date is disabled by default.
	Diagnostics	The option OS Agent Requests
	Power-on-Self-Test Automatic Recovery	The option is enabled by default.

Table 12. System setup options—Keyboard menu The following table describes the Keyboard menu options in the System setup program.
Keyboard
	Keyboard Errors
	Enable Keyboard Error Detection	Enable or disable the keyboard error detection. By default, the option is enabled.
	Numlock LED
	Enable Numlock LED	Enable or disable Numlock LED. By default, the option is enabled.
	Device Configuration Hotkey Access
	Device Configuration Hotkey Access	Enable or disable users to access device configuration by using hotkeys. By default, the option is enabled.

Table 13. System setup options—Pre-boot Behavior menu The following table describes the Pre-boot Behavior menu options in the System setup program.
Pre-boot Behavior
	Warning and Errors	Enable or disable the action to be done when a warning or error is encountered. By default, the Prompt on Warnings and Errors option is enabled.
	Fastboot	Enable to set the speed of the boot process. By default, the option is enabled.
	Extend BIOS POST Time	Set the BIOS POST time. By default, the 0 seconds option is enabled.

Table 14. System setup options—Virtualization menu The following table describes the Virtualization menu options in the System setup program.
Virtualization
	Intel Virtualization Technology
	Enable Intel Virtualization Technology (VT)	Specify whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities that are provided by Intel Virtualization Technology. By default, the option is enabled.
	VT for Direct I/O	Specify whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities that are provided by Intel Virtualization Technology for Direct I/O. By default, the option is enabled.
	Intel Trusted Execution Technology (TXT)
	Enable Intel Trusted Execution Technology (TXT)	Specifies whether a measured Virtual Machine Monitor (MVMM) can utilize the additional hardware capabilities that are provided by Intel Trusted Execution Technology. By default, the option is disabled.
	DMA Protection
	Enable Pre-Boot DMA Support	The option is enabled by default.
	Enable OS Kernel DMA Support	The option is enabled by default.

Table 15. System setup options—Performance menu The following table describes the Performance menu options in the System setup program.
Performance
	Multi Core Support
	Active Cores	Enables to change the number of CPU cores available to the operating system. By default, the All Cores options are enabled.
	Intel SpeedStep
	Enable Intel SpeedStep Technology	Enables the computer to dynamically adjust processor voltage and core frequency, decreasing average power consumption and heat production. By default, the option is enabled.
	C-States Control
	Enable C-State Control	Enable or disable additional processor sleep states. By default, the option is enabled.
	Intel Turbo Boost Technology
	Enable Intel Turbo Boost Technology	Enable or disable Intel TurboBoost mode of the processor. By default, the option is enabled.
	Intel Hyper-Threading Technology
	Enable Intel Hyper-Threading Technology	Enable or disable Hyper-Threading in the processor. By default, the option is enabled.
	PCIe Resizable Base Address Register (BAR)	This option is disabled by default.

Table 16. System setup options—System Logs menu
The following table describes the System Logs menu options in the System setup program.
System Logs
	BIOS Event Log
	Clear BIOS Event Log	Display BIOS events. By default, the Keep option is enabled.