Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

show dot1x interface

Display the 802.1X configuration of an interface.

Syntax

show dot1x interface interface [mac-address mac-address]

Parameters

interface	Enter one of the following keywords and slot/port or number information: For a Ten-Gigabit Ethernet interface, enter the keyword `TenGigabitEthernet` then the slot/port information.
mac-address	(Optional) MAC address of a supplicant.

Defaults

none

Command Modes

EXEC
EXEC privilege

Supported Modes

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.2(0.0)	Introduced on the MXL 10/40GbE Switch IO Module.

Usage Information

If you enable 802.1X multi-supplicant authentication on a port, additional 802.1X configuration details (Port Authentication status, Untagged VLAN ID, Authentication PAE state, and Backend state) are displayed for each supplicant, as shown in the following example.

Example

Dell#show dot1x interface tengigabitethernet 0/1
                                             
                                             802.1x information on Te 0/1:
                                             -----------------------------
                                             Dot1x Status:             Enable
                                             Port Control:             AUTO
                                             Port Auth Status:         AUTHORIZED(MAC-AUTH-BYPASS)
                                             Re-Authentication:        Disable
                                             Untagged VLAN id:         400
                                             Guest VLAN:               Enable
                                             Guest VLAN id:            100
                                             Auth-Fail VLAN:           Disable
                                             Auth-Fail VLAN id:        NONE
                                             Auth-Fail Max-Attempts:   NONE
                                             Mac-Auth-Bypass:          Enable
                                             Mac-Auth-Bypass Only:     Enable
                                             Tx Period:                3 seconds
                                             Quiet Period:             60 seconds
                                             ReAuth Max:               2
                                             Supplicant Timeout:       30 seconds
                                             Server Timeout:           30 seconds
                                             Re-Auth Interval:         3600 seconds
                                             Max-EAP-Req:              2
                                             Host Mode:                SINGLE_HOST
                                             Auth PAE State:           Authenticated
                                             Backend State:            Idle
                                             Dell#
                                             
                                             Dell#show dot1x interface tengigabitethernet 0/1 mac-address 00:00:00:00:00:10
                                             Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac:
                                             
                                             802.1x information on Te 0/1:
                                             -----------------------------
                                             Dot1x Status:             Enable
                                             Port Control:             AUTO
                                             Re-Authentication:        Disable
                                             Guest VLAN:               Enable
                                             Guest VLAN id:            100
                                             Auth-Fail VLAN:           Disable
                                             Auth-Fail VLAN id:        NONE
                                             Auth-Fail Max-Attempts:   NONE
                                             Mac-Auth-Bypass:          Enable
                                             Mac-Auth-Bypass Only:     Enable
                                             Tx Period:                3 seconds
                                             Quiet Period:             60 seconds
                                             ReAuth Max:               2
                                             Supplicant Timeout:       30 seconds
                                             Server Timeout:           30 seconds
                                             Re-Auth Interval:         3600 seconds
                                             Max-EAP-Req:              2
                                             Host Mode:                MULTI_AUTH
                                             Max-Supplicants:          128
                                             
                                             Port status and State info for Supplicant: 00:00:00:00:00:10
                                             
                                             Port Auth Status:         AUTHORIZED(MAC-AUTH-BYPASS)
                                             Untagged VLAN id:         400
                                             Auth PAE State:           Authenticated
                                             Backend State:            Idle
                                             Dell#