Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

show ip ospf interface

Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated.

Syntax

show ip ospf process-id interface [ interface]

Parameters

process-id

Enter the OSPF process ID to show a specific process. If you do not enter a process ID, the command applies only to the first OSPF process.

interface

(OPTIONAL) Enter the following keywords and slot/port or number information:

For the null interface, enter the keyword null then zero (0).
For Loopback interfaces, enter the keyword loopback then a number from 0 to 16383.
For Port Channel groups, enter the keywords port-channel then a number. The range is from 1 to 128.
For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
For a VLAN, enter the keyword vlan then the VLAN ID. The range is from 1 to 4094.

Command Modes

EXEC
EXEC Privilege

Supported Modes

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
8.3.16.1	Introduced on the MXL 10/40GbE Switch IO Module.

Usage Information

The following describes the show ip ospf process-id interface command shown in the following example.

Item	Description
TenGigabitEthernet...	This line identifies the interface type slot/port and the status of the OSPF protocol on that interface.
Internet Address...	This line displays the IP address, network mask and area assigned to this interface.
Process ID...	This line displays the OSPF Process ID, Router ID, Network type and cost metric for this interface.
Transmit Delay...	This line displays the interface’s settings for Transmit Delay, State, and Priority. In the State setting, BDR is Backup Designated Router.
Designated Router...	This line displays the ID of the Designated Router and its interface address.
Backup Designated...	This line displays the ID of the Backup Designated Router and its interface address.
Timer intervals...	This line displays the interface’s timer settings for Hello interval, Dead interval, Transmit Delay (Wait), and Retransmit Interval.
Hello due...	This line displays the amount time until the next Hello packet is sent out this interface.
Neighbor Count...	This line displays the number of neighbors and adjacent neighbors. Listed below this line are the details about each adjacent neighbor.

Example

Dell>show ip ospf int
                                             
                                             TenGigabitEthernet 1/1 is up, line protocol is up
                                             Internet Address 192.168.1.2/30, Area 0.0.0.1
                                             Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1
                                             Transmit Delay is 1 sec, State DR, Priority 1
                                             Designated Router (ID) 192.168.253.2, Interface address 192.168.1.2
                                             Backup Designated Router (ID) 192.168.253.1, Interface address 192.168.1.1
                                             Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
                                             Hello due in 00:00:02
                                             Neighbor Count is 1, Adjacent neighbor count is 1
                                             Adjacent with neighbor 192.168.253.1 (Backup Designated Router)
                                             
                                             TenGigabitEthernet 1/2 is up, line protocol is up
                                             Internet Address 192.168.0.1/24, Area 0.0.0.1
                                             Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1
                                             Transmit Delay is 1 sec, State DROTHER, Priority 1
                                             Designated Router (ID) 192.168.253.5, Interface address 192.168.0.4
                                             Backup Designated Router (ID) 192.168.253.3, Interface address 192.168.0.2
                                             Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
                                             Hello due in 00:00:08
                                             Neighbor Count is 3, Adjacent neighbor count is 2
                                             Adjacent with neighbor 192.168.253.5 (Designated Router)
                                             Adjacent with neighbor 192.168.253.3 (Backup Designated Router)
                                             
                                             Loopback 0 is up, line protocol is up
                                             Internet Address 192.168.253.2/32, Area 0.0.0.1
                                             Process ID 1, Router ID 192.168.253.2, Network Type LOOPBACK, Cost: 1
                                             Loopback interface is treated as a stub Host.
                                             Dell>