Ga naar hoofdinhoud
Uitloggen

Welkom bij Dell

Mijn account
  • Snel en eenvoudig bestellen
  • Bestellingen en de verzendstatus bekijken
  • Een lijst met producten maken en openen
  • Beheer uw Dell EMC locaties, producten en contactpersonen op productniveau met Company Administration.
Inloggen Een account maken Inloggen bij Premier Aanmelden voor partnerprogramma
Contact

Uw Dell.com-winkelwagentjes

Dell PowerEdge FN I/O Module Configuration Guide 9.10(0.0)

PDF

Configuring and Adding the Member VLANs

Control and member VLANS are configured normally for Layer 2. Their status as Control or Member is determined at the FRRP group commands.

For more information about configuring VLANS in Layer 2 mode, refer to the Layer 2 chapter.
Be sure to follow these guidelines:
  • All VLANS must be in Layer 2 mode.
  • Tag control VLAN ports. Member VLAN ports, except the Primary/Secondary interface, can be tagged or untagged.
  • The control VLAN must be the same for all nodes on the ring.

To create the Members VLANs for this FRRP group, use the following commands on all of the Transit switches in the ring.

  1. Create a VLAN with this ID number. CONFIGURATION mode. interface vlan vlan-id VLAN ID: the range is from 1 to 4094.
  2. Tag the specified interface or range of interfaces to this VLAN. CONFIG-INT-VLAN mode. tagged interface slot/port { range}
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    • Slot/Port, range : Slot and Port ID for the interface. The range is entered Slot/Port-Port.
  3. Assign the Primary and Secondary ports and the Control VLAN for the ports on the ring. CONFIG-FRRP mode. interface primary int slot/port secondary int slot/port control-vlan vlan id
    • For a 10/100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information.
    • For a SONET interface, enter the keyword sonet then the slot/port information.
    • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information.
    Slot/Port, Range : Slot and Port ID for the interface. Range is entered Slot/Port-Port. VLAN ID : Identification number of the Control VLAN.
  4. Configure a Transit node. CONFIG-FRRP mode. mode transit
  5. Identify the Member VLANs for this FRRP group. CONFIG-FRRP mode. member-vlan vlan-id { range} VLAN-ID, Range : VLAN IDs for the ring’s Member VLANs.
  6. Enable this FRRP group on this switch. CONFIG-FRRP mode. no disable

Beoordeel deze inhoud

Nauwkeurig
Nuttig
Eenvoudig te begrijpen
Was dit artikel nuttig?
0/3000 characters
  Geef een beoordeling (1-5 sterren).
  Geef een beoordeling (1-5 sterren).
  Geef een beoordeling (1-5 sterren).
  Selecteer of het artikel nuttig is of niet.
  Opmerkingen mogen geen speciale tekens bevatten: <>() \