Zu den Hauptinhalten

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

PDF

restore factory-defaults

Restore factory defaults.

Syntax

restore factory-defaults stack-unit id {clear-all | nvram}

Parameters

factory-defaults	Return the system to its factory default mode.
id	Enter the stack member unit identifier to restore the mentioned stack-unit. The range is from 0 to 6. Enter the keyword `all` to restore all units in the stack.
clear-all	Enter the keywords `clear-all` to reset the NvRAM and the system startup configuration.
nvram	Enter the keyword `nvram` to reset the NvRAM only.

Command Modes

EXEC Privilege

Supported Modes

All Modes

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.4(0.0)	Supported on the FN I/O aggregator.
8.3.17.0	Supported on the M I/O Aggregator.

Usage Information

Restoring factory defaults deletes the existing startup configuration and all persistent settings (stacking, fanout, and so forth).

When restoring all units in a stack, all the units in the stack are placed into stand-alone mode.

When restoring a single unit in a stack, that unit placed in stand-alone mode. No other units in the stack are affected.

When restoring units in stand-alone mode, the units remin in stand-alone mode after the restoration. After the restore is complete, the units power cycle immediately.

CAUTION: There is no undo for this command.

Example

Dell#restore factory-defaults stack-unit 0 clear-all 
                                             
                                             ********************************************
                                             *Warning - Restoring factory defaults will delete the existing*
                                             *startup-config and resets all persistent settings (stacking,*
                                             *fanout, etc.) and boot environment variables (boot config, console*
                                             *baud rate, management interface settings, etc.)*
                                             *After restoration the unit(s) will be powercycled immediately.*
                                             *Proceed with caution !*
                                             **********************************************
                                             
                                             Proceed with factory settings? Confirm [yes/no]:yes
                                             
                                             -- Restore status --
                                             Unit   Nvram     Config    Bootvar
                                             -----------------------------------
                                             0    Success   Success   Success
                                             Dell#

Example (NvRAM, all)

Dell#restore factory-defaults stack-unit all nvram
                                             *************************************************
                                             *Warning - Restoring factory defaults will delete the existing*
                                             *persistent settings (stacking, fanout, etc.)*
                                             *All the units in the stack will be split into standalone units.*
                                             *After restoration the unit(s) will be powercycled immediately.*
                                             *Proceed with caution ! *
                                             **************************************************
                                             Proceed with factory settings? Confirm [yes/no]:yes
                                             -- Restore status --
                                             Unit Nvram      Config
                                             ------------------------
                                             0    Success
                                             1    Success
                                             2    Success
                                             3    Not present
                                             4    Not present
                                             5    Not present
                                             Power-cycling the unit(s).
                                             Dell#

Example (NvRAM, single unit)

Dell#restore factory-defaults stack-unit 1 nvram
                                             **********************************************
                                             *Warning - Restoring factory defaults will delete the existing *
                                             *persistent settings (stacking, fanout, etc.) *
                                             *After restoration the unit(s) will be powercycled immediately. *
                                             *Proceed with caution ! *
                                             **********************************************
                                             Proceed with factory settings? Confirm [yes/no]:yes
                                             -- Restore status --
                                             Unit Nvram   Config
                                             ------------------------
                                             1    Success
                                             Power-cycling the unit(s).
                                             Dell#