Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

show mac-address-table

Display the MAC address table.

show mac-address-table [dynamic | static] [address mac-address | interface interface | vlan vlan-id] [count [vlan vlan-id] [interface interface-type [ slot [ /port]]]]

Parameters

dynamic	(OPTIONAL) Enter the keyword `dynamic` to display only those MAC addresses the switch dynamically learns. Optionally, you can also add one of these combinations: `address/ mac-address`, `interface/ interface`, or `vlan vlan-id`.
static	(OPTIONAL) Enter the keyword `static` to display only those MAC addresses specifically configured on the switch. Optionally, you can also add one of these combinations: `address/ mac-address`, `interface/ interface`, or `vlan vlan-id`.
address mac-address	(OPTIONAL) Enter the keyword `address` then a MAC address in the nn:nn:nn:nn:nn:nn format to display information on that MAC address.
interface interface	(OPTIONAL) Enter the keyword `interface` then the interface type, slot and port information: For a Port Channel interface, enter the keywords `port-channel` then a number. The range is from 1 to 128. For a 10-Gigabit Ethernet interface, enter the keyword `TenGigabitEthernet` then the slot/port information.
interface interface-type	(OPTIONAL) Instead of entering the keyword `interface` then the interface type, slot and port information, as above, you can enter the interface type, then just a slot number.
vlan vlan-id	(OPTIONAL) Enter the keyword `vlan` then the VLAN ID to display the MAC address assigned to the VLAN. The range is 1 to 4094.
count	(OPTIONAL) Enter the keyword `count`, then optionally, by an interface or VLAN ID, to display total or interface-specific static addresses, dynamic addresses, and MAC addresses in use.

Command Modes

EXEC
EXEC Privilege

Supported Modes

Programmable-Mux (PMUX)

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.4(0.0)	Supported on the FN I/O Aggregator.
9.2(0.0)	Introduced on the M I/O Aggregator.

Usage Information

The following describes the show mac-address-table command shown in the following example.

Column Heading	Description
VlanId	Displays the VLAN ID number.
Mac Address	Displays the MAC address in nn:nn:nn:nn:nn:nn format.
Type	Lists whether the MAC address was manually configured (Static), learned dynamically (Dynamic), or associated with a specific port (Sticky).
Interface	Displays the interface type and slot/port information. The following abbreviations describe the interface types: gi — Gigabit Ethernet then a slot/port. po — Port Channel then a number. The range is from 1 to 255 for TeraScale. so —SONET then a slot/port. te — 10 Gigabit Ethernet then a slot/port.
State	Lists if the MAC address is in use (Active) or not in use (Inactive).

Example

Dell#show mac-address-table
                                             VlanId Mac Address       Type     Interface  State
                                             20     00:00:c9:ad:f6:12 Dynamic  Te 0/3     Active
                                             Dell#

Usage Information

The following describes the show mac-address-table command shown in the following example.

Column Heading	Description
VlanId	Displays the VLAN ID number.
Mac Address	Displays the MAC address in nn:nn:nn:nn:nn:nn format.
Type	Lists whether the MAC address was manually configured (Static), learned (Dynamic), or associated with a specific port (Sticky). An (N) indicates that the specified MAC address has been learnt by a neighbor and is synced to the node.
Interface	Displays the interface type and slot/port information. The following abbreviations describe the interface types: gi — Gigabit Ethernet then a slot/port po — Port Channel then a number. The range is from 1 to 255. \ so — SONET then a slot/port. te — 10–Gigabit Ethernet then a slot/port.
State	Lists if the MAC address is in use (Active) or not in use (Inactive).

The following describes the show mac-address-table count command shown in the following example.

Line Beginning With	Description
MAC Entries...	Displays the number of MAC entries learned per VLAN.
Dynamic Address...	Lists the number of dynamically learned MAC addresses.
Static Address...	Lists the number of user-defined MAC addresses.
Total MAC...	Lists the total number of MAC addresses the switch uses.

Example (Count)

Dell#show mac-address-table count
                                             MAC Entries for all vlans :
                                             Dynamic Address Count :                5
                                             Static Address (User-defined) Count :  0
                                             Total MAC Addresses in Use:            5
                                             Dell#

Willkommen

Willkommen bei Dell

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

show mac-address-table

Diesen Inhalt bewerten