- Notes, cautions, and warnings
- About this document
- PowerEdge R660 system overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Cooling fan specifications
- Supported operating systems
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Cooling fans
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing the drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Drive backplane
- Side wall brackets
- PERC modules
- Rear drive module
- Cable routing
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the A2 Blank from the expansion card riser
- Installing the A2 Blank on to the expansion card riser
- Removing the VGA port
- Installing the VGA port
- Intrusion switch
- M.2 SSD module
- Optional BOSS-N1 module
- System battery
- Optional OCP NIC card
- Optional internal USB card
- VGA module
- Power supply unit
- Optional serial COM port
- System board
- LOM card, MIC card, and rear I/O board
- Control panel
- Trusted Platform Module
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Using system diagnostics
- Getting help
- Documentation resources
Dell PowerEdge R660 Installation and Service Manual
PowerEdge R660 system overview
The
PowerEdge
R660
system is a 1U server that supports:
- Up to two 4th Gen Intel® Xeon® Scalable or Intel® Xeon® Max Processors with up to 56 cores
- Up to two 5th Gen Intel® Xeon® Scalable Processors with up to 64 cores
- Direct Liquid Cooling
- 32 DIMM slots
- Two redundant AC or DC power supply units
- Up to 8 x 2.5-inch or 10 x 2.5-inch SAS or SATA or NVMe (HDD/SSD) drives. 14 x EDSFF E3.S 16 x EDSFF E3.S drives.
NOTE: For more information about how to hot swap NVMe PCIe SSD U.2 device, see the
Dell Express Flash NVMe PCIe SSD User's Guide at
https://www.dell.com/support.
NOTE:All instances of SAS, SATA drives are referred to as drives in this document, unless specified otherwise.
CAUTION: Do not install GPUs, network cards, or other PCIe devices on your system that are not validated and tested by Dell. Damage caused by unauthorized and invalidated hardware installation will null and void the system warranty.
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
本文章是否有幫助？請選擇。
評語中不得包含下列特殊字元：<>()\