- Notes, cautions, and warnings
- About this document
- PowerEdge R660 system overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Cooling fan specifications
- Supported operating systems
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Cooling fans
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing the drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Drive backplane
- Side wall brackets
- PERC modules
- Rear drive module
- Cable routing
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the A2 Blank from the expansion card riser
- Installing the A2 Blank on to the expansion card riser
- Removing the VGA port
- Installing the VGA port
- Intrusion switch
- M.2 SSD module
- Optional BOSS-N1 module
- System battery
- Optional OCP NIC card
- Optional internal USB card
- VGA module
- Power supply unit
- Optional serial COM port
- System board
- LOM card, MIC card, and rear I/O board
- Control panel
- Trusted Platform Module
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Using system diagnostics
- Getting help
- Documentation resources
Dell PowerEdge R660 Installation and Service Manual
Removing the 14 x EDSFF E3.S drive backplane
Prerequisites
CAUTION:To prevent damage to the drives and backplane, remove the drives from the system before removing the backplane.
CAUTION:Note the number of each drive and temporarily label them before you remove the drive so that you can reinstall them in the same location.
NOTE:The procedure to remove the backplane is similar for all backplane configurations.
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in Before working inside your system.
- If installed, remove the air shroud.
- Remove the drive backplane cover.
- Remove the drive carrier.
- Observe and disconnect the drive backplane cables from the connector on the system board and backplane.
NOTE:Refer cable routing topic for more information.
Steps
- Using a Phillips #1 screwdriver, loosen the captive screw on the backplane module.
- Slide the backplane and lift it away from the system.
NOTE:To avoid damaging the backplane, ensure that you move the control panel cables from the cable routing clips before removing the backplane.
Figure 1. Removing the 14 xEDSFF E3.S drive backplane 
Next steps
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
本文章是否有幫助？請選擇。
評語中不得包含下列特殊字元：<>()\