- Notes, cautions, and warnings
- About this document
- PowerEdge R660 system overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Cooling fan specifications
- Supported operating systems
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Cooling fans
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing the drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Drive backplane
- Side wall brackets
- PERC modules
- Rear drive module
- Cable routing
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the A2 Blank from the expansion card riser
- Installing the A2 Blank on to the expansion card riser
- Removing the VGA port
- Installing the VGA port
- Intrusion switch
- M.2 SSD module
- Optional BOSS-N1 module
- System battery
- Optional OCP NIC card
- Optional internal USB card
- VGA module
- Power supply unit
- Optional serial COM port
- System board
- LOM card, MIC card, and rear I/O board
- Control panel
- Trusted Platform Module
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Using system diagnostics
- Getting help
- Documentation resources
Dell PowerEdge R660 Installation and Service Manual
System board jumpers and connectors
| Item | Connector | Description |
|---|---|---|
| 1. | Rear I/O connector | Rear I/O connector |
| 2. | IO_RISER3 (CPU2) | Riser 3 |
| 3. | B9, B1, B15, B7, B11, B3, B13, B5 | DIMM for CPU 2 channels A, B, C, D |
| 4 | SL10_PCH_SA1 1 | SATA Connector |
| 5. | IO_RISER2_A (CPU1) and IO_RISER2_B (CPU2) | Riser 2 |
| 6. | TPM | TPM connector |
| 7. | OCP | OCP NIC 3.0 connector |
| 8. | SL13_CPU1_PB7 | PCIe connector 13 |
| 9. | Battery | Coin cell battery |
| 10. | LOM_Connector | LOM connector |
| 11. | IDSDM/ Internal USB | IDSDM/ Internal USB connector |
| 12. | SL11_CPU1_PB7 | PCIe connector 11 |
| 13. | IO_RISER1 (CPU1) | Riser 1 |
| 14. | SIG_PWR_0 | Power connector 0 - use for BP only |
| 15. | BOSS_PWR | BOSS card power |
| 16. | PUCK_PSU1 | PSU1 PUCK Sideband Signal |
| 17. | SL12_PCH_PA6 | PCIe connector 12 |
| 18. | FRONT_VIDEO | Front VGA connector |
| 19. | PWR1 | PWR1 |
| 20. | PSU | PSU connector 1 |
| 21. | CPU 1 | Processor 1 |
| 22. | A9, A1, A15, A7, A11, A3, A13, A5 | DIMM for CPU 1 channels A, B, C, D |
| 23. | SL8_CPU1_PA4 | PCIe connector 8 |
| 24. | RGT_CP | Right control panel connector |
| 25. | SIG_PWR_2 | Power connector 2 - use for BP only |
| 26. | FAN_1U4 | FAN 4 connector |
| 27. | SL7_CPU1_PB4 | PCIe connector 7 |
| 28. | SL4_CPU1_PB2 | PCIe connector 4 |
| 29. | FAN_1U3 | FAN 3 connector |
| 30. | SL3_CPU1_PA2 | PCIe connector 3 |
| 31. | SIG_PWR_1 | Power connector 1 - use for BP only |
| 32. | SL6_CPU2_PA3 | PCIe connector 6 |
| 33. | SL5_CPU2_PB3 | PCIe connector 5 |
| 34. | FAN_1U2 | FAN 2 connector |
| 35. | SL2_CPU2_PB1 | PCIe connector 2 |
| 36. | FAN_1U1 | FAN 1 connector |
| 37. | SL1_CPU1_PA1 | PCIe connector 1 |
| 38. | PWRD_EN and NVRAM_CLR | Jumper |
| 39. | LFT_CP | Left control panel connector |
| 40. | A8, A16, A2, A10, A6, A14, A4, A12 | DIMMs for CPU 1 channels H, G, F, E |
| 41. | CPU 2 | Processor 2 |
| 42. | B8, B16, B2, B10, B6, B14, B4, B12 | DIMMs for CPU 2 channels H, G, F, E |
| 43. | PSU | PSU connector 2 |
| 44. | PWR2 | PWR2 |
| 45. | PUCK_PSU2 | PSU 2 PUCK Sideband Signal |
| 46. | IO_RISER4 (CPU2) | Riser 4 |
| 47. | BAT_SIG | Battery signal |
| 48 | SL9_CPU2_PA5 1 | SATA Connector |
NOTE: The platform supports Maximum (MAX) and Mainstream (MS) system boards.
- 1 SL9_CPU2_PA5 and SL10_PCH_SA1 connectors are available only on MAX system board.
- MS system board supports CPU TDP < 250 W
- MAX system board supports CPU TDP => 250 W
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
本文章是否有幫助？請選擇。
評語中不得包含下列特殊字元：<>()\