- Notes, cautions, and warnings
- About this document
- PowerEdge R660 system overview
- Technical specifications
- Chassis dimensions
- System weight
- Processor specifications
- PSU specifications
- Cooling fan specifications
- Supported operating systems
- System battery specifications
- Expansion card riser specifications
- Memory specifications
- Storage controller specifications
- Drives
- Ports and connectors specifications
- Video specifications
- Environmental specifications
- Initial system setup and configuration
- Pre-operating system management applications
- System Setup
- Dell Lifecycle Controller
- Boot Manager
- PXE boot
- Minimum to POST and system management configuration validation
- Installing and removing system components
- Safety instructions
- Before working inside your system
- After working inside your system
- Recommended tools
- Optional front bezel
- System cover
- Drive backplane cover
- Air shrouds
- Cooling fans
- Drives
- Removing a drive blank
- Installing a drive blank
- Removing the drive carrier
- Installing the drive carrier
- Removing the drive from the drive carrier
- Installing the drive into the drive carrier
- Removing an EDSFF E3.S drive blank
- Installing an EDSFF E3.S drive blank
- Removing an EDSFF E3.S drive carrier
- Installing an EDSFF E3.S drive carrier
- Removing an EDSFF E3.S drive from the drive carrier
- Installing an EDSFF E3.S drive into the drive carrier
- Drive backplane
- Side wall brackets
- PERC modules
- Rear drive module
- Cable routing
- System memory
- Processor and heat sink module
- Expansion cards and expansion card risers
- Expansion card installation guidelines
- Removing the expansion card risers
- Installing the expansion card risers
- Removing expansion card from the expansion card riser
- Installing an expansion card into the expansion card riser
- Removing the A2 Blank from the expansion card riser
- Installing the A2 Blank on to the expansion card riser
- Removing the VGA port
- Installing the VGA port
- Intrusion switch
- M.2 SSD module
- Optional BOSS-N1 module
- System battery
- Optional OCP NIC card
- Optional internal USB card
- VGA module
- Power supply unit
- Optional serial COM port
- System board
- LOM card, MIC card, and rear I/O board
- Control panel
- Trusted Platform Module
- Upgrade Kits
- Jumpers and connectors
- System diagnostics and indicator codes
- Using system diagnostics
- Getting help
- Documentation resources
Dell PowerEdge R660 Installation and Service Manual
Removing the system board
Prerequisites
CAUTION:If you are using the Trusted Platform Module (TPM) with an encryption key, you may be prompted to create a recovery key during program or System Setup. Be sure to create and safely store this recovery key. If you replace this system board, you must supply the recovery key when you restart your system or program before you can access the encrypted data on your drives.
- Follow the safety guidelines listed in the Safety instructions.
- Follow the procedure listed in Before working inside your system.
- Remove the following components:
- Air shroud
or
PCH shroudNOTE:PCH shroud is installed on systems with no riser configuration.
- Cooling fan modules
- Processor and heat sink module
- Memory modules
- Expansion card riser
- Internal USB card (if installed)
- Side wall bracket
- OCP card (if installed)
- Power supply units (PSU)
- Disconnect all cables from the system board.
CAUTION:Take care not to damage the system identification button while removing the system board from the system.
- Air shroud
or
PCH shroud
Steps
- Using the system board holder and plunger, slide the system board towards the front of the system.
- Lift the system board out of the chassis.
Figure 1. Removing the system board 
Next steps
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
請給予評分 (1 到 5 顆星)。
本文章是否有幫助？請選擇。
評語中不得包含下列特殊字元：<>()\