Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

ip ssh server

Configure an SSH server.

ip ssh server {ciphers cipher-list} {enable | port port-number} [kex key-exchange-algorithm] [mac hmac-algorithm] [version {1 | 2}]

To disable SSH server functions, use the no ip ssh server {ciphers cipher-list} {enable | port port-number} {kex key-exchange-algorithm command.

Parameters

enable	Enter the keyword `enable` to start the SSH server.
ciphers cipher-list	Enter the keyword `ciphers` and then a space-delimited list of ciphers that the SSH server supports. The following ciphers are available. `3des-cbc` `aes128-cbc` `aes192-cbc` `aes256-cbc` `aes128-ctr` `aes192-ctr` `aes256-ctr` The default cipher list is used. `3des-cbc` `aes128-cbc` `aes192-cbc` `aes256-cbc` `aes128-ctr` `aes192-ctr` `aes256-ctr`
mac hmac-algorithm	Enter the keyword `mac` then a space-delimited list of hash message authentication code (HMAC) algorithms supported by the SSH server for keying hashing for the message authentication. The following HMAC algorithms are available: `hmac-sha1` `hmac-sha1-96` `hmac-sha2-256` When FIPS is enabled, the default HMAC algorithm is `hmac-sha1-96`. When FIPS is not enabled, the default HMAC algorithms are the following: `hmac-md5` `hmac-md5-96` `hmac-sha1` `hmac-sha1-96` `hmac-sha2-256`
kex key-exchange-algorithm	Enter the keyword `kex` and then a space-delimited list of key exchange algorithms supported by the SSH server. The following key exchange algorithms are available: `diffie-hellman-group-exchange-sha1` `diffie-hellman-group1-sha1` `diffie-hellman-group14-sha1` When FIPS is enabled, the default key-exchange-algorithm is `diffie-hellman-group14-sha1`. When FIPS is not enabled, the default key-exchange-algorithms are the following: `diffie-hellman-group-exchange-sha1` `diffie-hellman-group1-sha1,` `diffie-hellman-group14-sha1`
port port-number	(OPTIONAL) Enter the keyword `port` then the port number of the listening port of the SSH server. The range is from 1 to 65535. The default is 22.
[version {1 \| 2}]	(OPTIONAL) Enter the keyword `version` then the SSH version 1 or 2 to specify only SSHv1 or SSHv2. NOTE: If you enable FIPS mode, you can only select version 2.

Defaults

Default listening port is 22.

Command Modes

CONFIGURATION

Supported Modes

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.5(0.0)	Introduced the `cipher`, `kex` and `mac` options on the MXL 10/40GbE Switch.
8.3.16.1	Introduced on the MXL 10/40GbE Switch IO Module.

Usage Information

This command enables the SSH server and begins listening on a port. If a port is not specified, listening is on SSH default port 22.

NOTE: Starting with Dell Networking OS Release 9.2(0.0), SSH server is enabled by default.

Example

Dell# conf
                                             Dell(conf)# ip ssh server port 45
                                             Dell(conf)# ip ssh server enable
                                             Dell#

Related Commands

show ip ssh — displays the ssh information.

Welcome

Welcome to Dell

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

ip ssh server

Rate this content