Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

cam-acl (Configuration)

Select the default CAM allocation settings or reconfigure a new CAM allocation for Layer 2, IPv4, and IPv6 ACLs, Layer 2 and Layer 3 (IPv4) QoS, Layer 2 Protocol Tunneling (L2PT), IP and MAC source address validation for DHCP, Ethernet Connectivity Fault Management (CFM) ACLs, and Policy-based Routing (PBR).

Syntax

cam-acl {default | l2acl number ipv4acl number ipv6acl number ipv4qos number l2qos number l2pt number ipmacacl number [vman-qos | vman-qos—dual— number | vman-qos—dual—fp number] ipv4pbr number} ecfmacl number [nlbclusteracl number]fcoeacl number iscsioptacl number}

Parameters

default	Use the default CAM profile settings and set the CAM as follows: L3 ACL (ipv4acl): 4 L2 ACL(l2acl): 5 IPv6 L3 ACL (ipv6acl): 0 L3 QoS (ipv4qos): 1 L2 QoS (l2qos): 1 L2PT (L2PT): 0 MAC ACL (IpMacAcl): 0 VmanDualQos: 0 EcfmAcl: 0 nlbclusteracl: 0 FcoeAcl: 4 iscsiOptAcl: 2
l2acl number	Enter the keyword `l2acl` and then the number of l2acl blocks. The range is from 1 to 8.
ipv4acl number	Enter the keyword `ipv4acl` and then the number of FP blocks for IPv4. The range is from 0 to 8.
ipv6acl number	Enter the keyword `ipv6acl` and then the number of FP blocks for IPv6. The range is from 0 to 4.
ipv4qos number	Enter the keyword `ipv4qos` and then the number of FP blocks for IPv4. The range is from 0 to 8.
l2qos number	Enter the keyword `l2qos` and then the number of FP blocks for l2 qos. The range is from 1to 8.
l2pt number	Enter the keyword `l2pt` and then the number of FP blocks for l2 protocol tunnelling. The range is from 0 to 1.
Ipmacacl number	Enter the keyword `ipmacacl` and then the number of FP blocks for IP and MAC ACL. The range is from 0 to 6.
ecfmacl number	Enter the keyword `ecfmacacl` and then the number of FP blocks for ECFM ACL. The range is from 0 to 5.
nlbclusteracl number	Enter the keyword `nlbclusteracl` and then the number of FP blocks for nlbcluster ACL. The range is from 0 to 2. By default the value is 0 and it supports eight NLB arp entries reserved for internal functionality. NOTE: When you reconfigure CAM allocation, use the `nlbclusteracl number` command to change the number of NLB ARP entries. The range is from 0 to 2. The default value is 0. At the default value of 0, eight NLB ARP entries are available for use. This platform supports upto 256 CAM entries. Select 1 to configure 128 entries. Select 2 to configure 256 entries. Even though you can perform CAM carving to allocate the maximum number of NLB entries, Dell Networking recommends that you use a maximum of 64 NLB ARP entries.
Vman-qos\|vman-dual-qos number	Enter the keyword `evman-qos` and then the number of FP blocks for VMAN QoS. The range is from 0 to 6.
vman-dual-qos number	Enter the keyword `vman-dual-qos` and then the number of FP blocks for VMAN dual QoS. The range is from 0 to 4.
Ipv4pbr number	Enter the keyword `ipv4pbr` and then the number of FP blocks for ipv4pbr ACL. The range is from 0 to 8.
Openflow number	Enter the keyword `openflow` and then the number of FP blocks for open flow (multiples of 4). The range is from 0 to 8.
fcoeacl number	Enter the keyword `fcoeacl` and then the number of FP blocks for FCOE ACL. The range is from 0 to 6.
Iscsioptacl number	Enter the keyword `iscsioptacl` and then the number of FP blocks for iSCSI optimization ACL. The range is from 0 to 2.
l2acl number ipv4acl number ipv6acl number, ipv4qos number l2qos number, l2pt number ipmacacl number ecfmacl number [vman-qos \| vman--qos-dual number \| vman-qos-dual-fp number] ipv4pbr number	Allocate space to each CAM region. Enter the CAM profile name then the amount of CAM space to be allotted. The total space allocated must equal 13. The range for ipv4acl is from 1 to 4. The ipv6acl range must be a factor of 2. The total space allocated must equal 13. The range for `ipv4acl` is 1 to 4. The `ipv6acl` range must be a factor of 2. The `vman-qos-dual-fp number` must be entered as a multiple of 4.

Command Modes

CONFIGURATION

Supported Modes

Full–Switch

Command History

Version	Description
9.9(0.0)	Introduced on the FN IOM.
9.7(0.0)	Added the keyword `nlbcluster ACL`.
9.4.(0.0)	Added support for PBR.
8.3.16.1	Introduced on the MXL 10/40GbE Switch IO Module.

Usage Information

Save the new CAM settings to the startup-config ( write-mem or copy run start) then reload the system for the new settings to take effect.

The total amount of space allowed is 16 FP Blocks. System flow requires three blocks; these blocks cannot be reallocated. The ipv4acl profile range is from 1 to 4.

When configuring space for IPv6 ACLs, the total number of Blocks must equal 13.

On the switch, there can be only one odd number of Blocks in the CLI configuration; the other Blocks must be in factors of two. For example, a CLI configuration of 5+4+2+1+1 Blocks is not supported; a configuration of 6+4+2+1 Blocks is supported.

Ranges for the CAM profiles are from 1 to 10, except for the ipv6acl profile which is from 0 to 10. The ipv6acl allocation must be a factor of two (2, 4, 6, 8, 10).

Welcome

Welcome to Dell

Dell PowerEdge FN I/O Module Command Line Reference Guide 9.10(0.0)

cam-acl (Configuration)

Rate this content