メイン コンテンツに進む
ログアウト

Dellへようこそ

マイアカウント
  • すばやく簡単にご注文が可能
  • 注文内容の表示、配送状況をトラック
  • 会員限定の特典や割引のご利用
  • 製品リストの作成とアクセスが可能
  • 「Company Administration（会社情報の管理）」では、お使いのDell EMCのサイトや製品、製品レベルでのコンタクト先に関する情報を管理できます。
ログイン アカウントの新規作成 プレミアログイン パートナー プログラム サインイン
お問い合わせ

Dell.comカート

Dell EMC SmartFabric OS10 User Guide Release 10.5.0

PDF

Installation using ONIE

CAUTION Installing OS10 or another OS using ONIE erases all software configurations on the switch. The configuration settings are not recoverable. Back up all software configurations and installed licenses on the switch before performing OS updates or changes. Store a regular backup of the switch configuration off the switch.
If you purchase an ONIE-only switch or if you want to replace an existing OS, download an OS10 image as described in Download OS10 image. Then install an OS10 software image using ONIE-based auto-discovery or a manual installation:
  • Automatic installation — ONIE discovers network information including the Dynamic Host Configuration Protocol (DHCP) server, connects to an image server, and downloads and installs an image automatically.
  • Manual installation — Manually configure your network information if a DHCP server is not available or if you install the OS10 software image using USB media.

System setup

Before installation, verify that the system is connected correctly:
  • Connect a serial cable and terminal emulator to the console serial port — serial port settings are 115200 baud rate, 8 data bits, and no parity.
  • Connect the Management port to the network to download an image over a network. To locate the Console port and the Management port, see the platform-specific Installation Guide at www.dell.com/support.

Install OS10

For an ONIE-enabled switch, go to the ONIE boot menu. An ONIE-enabled switch boots up with pre-loaded diagnostics (DIAGs) and ONIE software.

 +--------------------------------------------------------+
 |*ONIE: Install OS                                       |
 | ONIE: Rescue                                           |
 | ONIE: Uninstall OS                                     |
 | ONIE: Update ONIE                                      |
 | ONIE: Embed ONIE                                       |
 | ONIE: Diag ONIE                                        |
 +--------------------------------------------------------+
  • Install OS — Boots to the ONIE prompt and installs an OS10 image using the Automatic Discovery process. When ONIE installs a new OS image, the previously installed image and OS10 configuration are deleted.
  • Rescue — Boots to the ONIE prompt and enables manual installation of an OS10 image or ONIE update.
  • Uninstall OS — Deletes the contents of all disk partitions, including the OS10 configuration, except ONIE and diagnostics.
  • Update ONIE — Installs a new ONIE version.
  • Embed ONIE — Formats the disk and installs ONIE.
  • EDA DIAG — Runs the system diagnostics.

After the ONIE process installs an OS10 image and you later reboot the switch in ONIE: Install OS mode (default), ONIE takes ownership of the system and remains in Install mode (ONIE Install mode is sticky) until an OS10 image successfully installs again. To boot the switch from ONIE for any reason other than installation, select the ONIE: Rescue or ONIE: Update ONIE option from the ONIE boot menu.

CAUTION During an automatic or manual OS10 installation, if an error condition occurs that results in an unsuccessful installation and if there is an existing OS on the device, select Uninstall OS to clear the partitions. If the problem persists, contact Dell EMC Technical Support.

このコンテンツを評価する

正確
有益
分かりやすい
この記事は役に立ちましたか?
0/3000 characters
  1～5個の星の数で評価してください。
  1～5個の星の数で評価してください。
  1～5個の星の数で評価してください。
  この記事は役に立ちましたか?
  コメントでは、以下の特殊文字は利用できません: <>()\