Dell EMC SmartFabric OS10 User Guide Release 10.5.0

Sample FC Switch configuration on non-VLT network

1. Enable the F_PORT mode.

   OS10(config)# feature fc domain-id 1

2. Create the FC zones.

   OS10(config)# fc zone zoneA
   OS10(config-fc-zone-zoneA)# member wwn 10:00:00:90:fa:b8:22:19 <<Enter the WWN of Initiator CNA>>
   OS10(config-fc-zone-zoneA)# member wwn 21:00:00:24:ff:7b:f5:c8 <<Enter the WWN of Target>>

3. Create the FC zoneset.

   OS10(config)# fc zoneset zonesetA
   OS10(conf-fc-zoneset-zonesetA)# member zoneA

4. Create the vfabric VLAN.

   OS10(config)# interface vlan 1001
   

5. Create vfabric and activate the FC zoneset.

   OS10(config)# vfabric 1
   OS10(conf-vfabric-1)# vlan 1001
   OS10(conf-vfabric-1)# fcoe fcmap 0xEFC00
   OS10(conf-vfabric-1)# zoneset activate zonesetA
   

6. Enable DCBX.

   OS10(config)# dcbx enable

7. Apply the vfabric on the interfaces.

   OS10(config)# interface port-channel 10
   OS10(conf-if-po-10)# no shutdown
   OS10(conf-if-po-10)# switchport mode trunk
   OS10(conf-if-po-10)# switchport access vlan 1
   OS10(conf-if-po-10)# switchport trunk allowed vlan 10
   OS10(conf-if-po-10)# vfabric 1
   

   OS10(config)# interface fibrechannel 1/1/26
   OS10(conf-if-fc1/1/26)# description target_connected_port
   OS10(conf-if-fc1/1/26)# no shutdown
   OS10(conf-if-fc1/1/26)# vfabric 1

8. Apply the PFC configuration on the downlink interfaces. Include the interfaces to the port-channel and configure one of the interfaces as pinned-port.

   OS10(config)# interface ethernet 1/1/9
   OS10(conf-if-eth1/1/9)# no shutdown
   OS10(conf-if-eth1/1/9)# channel-group 10 mode active
   OS10(conf-if-eth1/1/9)# fcoe-pinned-por
   OS10(conf-if-eth1/1/9)# no switchport
   OS10(conf-if-eth1/1/9)# service-policy input type network-qos PFC
   OS10(conf-if-eth1/1/9)# priority-flow-control mode on
   

   OS10(config)# interface ethernet 1/1/10
   OS10(conf-if-eth1/1/10)# no shutdown
   OS10(conf-if-eth1/1/10)# channel-group 10 mode active
   OS10(conf-if-eth1/1/10)# no switchport
   OS10(conf-if-eth1/1/10)# service-policy input type network-qos PFC
   OS10(conf-if-eth1/1/10)# priority-flow-control mode on

View configuration

OS10# show fc ns switch brief
Total number of devices = 2
Intf#                    Domain    FC-ID            Enode-WWPN            Enode-WWNN
port-channel10(Eth 1/1/9) 1      01:00:00        20:01:f4:e9:d4:a4:7d:c3  20:00:f4:e9:d4:a4:7d:c3
fibrechannel1/1/26        1      01:68:00        21:00:00:24:ff:7c:ae:0e  21:00:00:24:ff:7c:ae:0e

vFabric id: 1
Active Zoneset: zonesetA
ZoneName                         ZoneMember
===========================================================
zoneA                            *20:01:f4:e9:d4:a4:7d:c3  
                                 *21:00:00:24:ff:7c:ae:0e

OS10# show fcoe pinned-port
Interface             pinned-port         FCoE Status
----------------- ---------------- -----------------
Po 10                  Eth 1/1/9                   Up